Marine Electronics Install & Repair in Corpus Christi, TX
Subtropical Gulf Coast climate.
For marine electronics install & repair, the service area covers roughly 40 miles from central Corpus Christi.
Common reasons to call
- A fishfinder or chartplotter screen goes black, freezes, or shows a fuzzy picture
- A new or used boat needs a full set of electronics wired up at the helm
- The VHF radio stopped sending or receiving clearly
- Salt water and damp air corroded the wiring or connectors
- The owner wants to add radar, an autopilot, or a trolling motor to an older boat
- The stereo, speakers, or courtesy lights quit working
Typical work
- Mounting and wiring a new fishfinder with the right transducer
- Setting up a networked chartplotter and radar at the helm
- Tracing and fixing corroded, loose, or melted wiring
- Installing a VHF radio and antenna
- Wiring a trolling motor with its own batteries and charger
- Building a clean NMEA network so all the devices share info
Typical turnaround
A single swap often takes a few hours. A full networked helm build usually runs a few days to a couple of weeks, depending on parts, boat access, and weather.
Materials and equipment
- Marine grade tinned copper wire
- Heat shrink connectors and dielectric grease
- Transducers (transom mount, thru-hull, or in-hull)
- NMEA 2000 network cables, tees, and terminators
- Marine fuses, breakers, and bus bars
- Stainless steel mounts and hardware
- Waterproof sealant and cable glands
- Sealed battery switches and chargers
Job sizes
Minor
Swapping a single unit like a VHF radio or stereo head, or fixing one blown fuse or loose connection.
Standard
Installing a new chartplotter or fishfinder with a transducer, running fresh wiring, and tying in a few devices.
Major
A full helm build with a networked chartplotter, radar, and autopilot all sharing one NMEA backbone.
Replacement
Pulling out old, corroded electronics across the whole boat and building a fresh system from the battery up.
Final pricing comes from the on-call provider after on-site assessment, with a written estimate before any work starts.
What to expect
- ✓A good pro uses marine grade tinned wire and sealed connectors so salt air does not eat the connections.
- ✓They label the wires and leave you a simple diagram so future work is easier.
- ✓They mount the transducer where it reads clean water, which is what actually makes a fishfinder work.
- ✓They protect every circuit with the right fuse or breaker so a short does not start a fire.
- ✓They test every device out on the water, not just sitting at the dock.
- ✓They follow common marine wiring practices like ABYC guidance even though no state license is required.
Voluntary NMEA installer certification, working knowledge of ABYC marine wiring standards, manufacturer training for the gear on your helm, and general liability insurance.
Common questions
Do marine electronics installers need a license in Texas?
No state trade license is required to install boat electronics. Many careful installers hold voluntary NMEA certification and follow ABYC wiring standards. The radios themselves fall under FCC rules for how they are used on the water, not for who installs them.
Why does my fishfinder show a blank or fuzzy screen?
It could be transducer placement, corrosion, water inside a connector, low voltage, or a failing unit. A good pro checks power and wiring first before blaming the screen itself.
Can I add modern electronics to an older boat?
Usually yes. Most older boats can take newer gear. The pro checks that your batteries and wiring can handle the extra load and often runs new cable to do it right.
What is a NMEA 2000 network?
It is a shared wiring backbone that lets your GPS, fishfinder, radar, and other gear talk to each other and share info. It keeps the helm cleaner than running each device on its own wires.
How long does a full helm install take?
It depends on how many devices you have and the weather. A single swap can be a few hours, while a full networked build can take several days or more.
Why does salt water cause so many electrical problems on boats?
Salt air and moisture corrode plain wire and cheap connectors from the inside out. That is why marine grade tinned wire and sealed connections matter so much down here on the coast.
Do you work at the dock or does the boat come to a shop?
Both happen. Simple jobs can often be done at the dock, ramp, or your driveway. Bigger builds usually go to a shop where the work stays dry and organized.
Will I lose my saved waypoints and settings?
Ask about this up front. A good installer can often save and move your waypoints, but that is not always possible when switching between different brands.